# MCP quickstart — connect Claude or ChatGPT to PipSync in minutes

Source: https://pipsync.io/en/mcp-quickstart-guide
Last updated: 2026-07-04

This quickstart connects Claude or ChatGPT to your PipSync account over MCP in a few minutes: add the connector with the URL and token from your dashboard, confirm it can read your account, then prepare your first trade and confirm it in PipSync.

You do not install anything. MCP (Model Context Protocol) is a connector you add inside the assistant, and PipSync's connector is trading-scope only — it reads your accounts, closes or tightens positions you ask about and prepares new orders that PipSync places after you confirm them, but can never move or withdraw money. MCP access is in early access and is switched on per account.

## What you need for this quickstart

| | |
|---|---|
| Time | About 5 minutes once your broker account is connected to PipSync |
| PipSync account | A paid plan with at least one MT5, cTrader or Match-Trade account linked |
| Assistant | Claude or ChatGPT — or any MCP-compatible client with connector settings |
| Connection details | Your personal MCP URL and access token from the PipSync dashboard — keep them private |
| Access | Trading scope only; a new trade is placed only after you confirm it in PipSync, and closing or tightening a stop runs right away |
| Availability | Early access — enabled per account as the rollout reaches you |

## Quickstart: connect your assistant to PipSync

Do these in order. Steps 1–2 are in PipSync; steps 3–4 are in Claude or ChatGPT; steps 5–7 are your first safe test.

1. **Create your PipSync account and connect a broker** — Sign up at app.pipsync.io and link the MT5 (or cTrader / Match-Trade) account you want the assistant to reach. A paid plan (Starter or higher) is needed, because Free cannot link a broker account.
2. **Copy your MCP URL and access token** — In the dashboard, open the connectors/MCP settings and copy your personal MCP URL and access token. Treat the token like a password — anyone with it can read your account, close or cancel positions and prepare orders for your confirmation.
3. **Open the connector settings in your assistant** — In Claude or ChatGPT, go to the connectors (MCP) section where you add a custom tool server. This is the same place for both clients.
4. **Add the PipSync connector** — Paste your MCP URL, authenticate with your token, and save. PipSync then appears as a set of trading tools the assistant can call.
5. **Verify with a read-only prompt** — Ask something harmless first: “List my PipSync accounts” or “What are my open positions?” A correct answer from your live account confirms the connector works.
6. **Prepare your first trade — and confirm it in PipSync** — Ask it to open a small position. Your assistant prepares the order and gives you a link: open it, check the volume, SL and TP, and click Confirm in PipSync. Nothing is placed before that click.
7. **Set volume and SL/TP yourself** — Orders are sent exactly as the assistant specifies them (volume, SL, TP), and both stop-loss and take-profit are required: PipSync never adds them. PipSync's per-route sizing and position limits apply to signal-driven trades, not to MCP orders, so state the volume and SL/TP in your prompt.

## What do I need before I start?

Three things: a paid PipSync account (Starter or higher) with at least one broker account (MT5, cTrader or Match-Trade) connected, an assistant that supports MCP connectors (Claude or ChatGPT), and your personal MCP URL and access token from the PipSync dashboard.

You do not need a VPS, an EA or any local software. The connector is a URL the assistant calls; PipSync runs the trading side in the cloud.

## How do I add the PipSync connector in Claude or ChatGPT?

Open the connectors (MCP) settings in your assistant, choose to add a custom server, paste your PipSync MCP URL and authenticate with your token. Save, and the PipSync trading tools appear in that chat.

The steps are identical in Claude and ChatGPT because MCP is a shared standard. Keep the token private: it authenticates the connector, so anyone who has it could act on your account within its trading scope.

## The assistant doesn't show the PipSync tools — what now?

This is almost always one of three things. Work through them in order:

- MCP access isn't enabled on your account yet — it's early access and rolled out in stages; check the dashboard or contact support.
- The URL or token was pasted incompletely — re-copy both from the dashboard and re-authenticate.
- The assistant cached an old connection — remove the connector and add it again, then start a fresh chat.

## How do I place my first trade safely?

Start on a demo account and with read-only prompts until you trust the answers, then ask for a small trade. A new trade is only prepared by your assistant; you place it by confirming it in PipSync. Closing, cancelling a pending order and tightening a stop run right away.

Because access is trading-scope only, the connector can prepare and manage trades but can never withdraw funds. PipSync's per-route sizing limits do not apply to MCP orders, so a mistyped request is prepared as typed: set the volume and SL/TP yourself and check the confirmation page before you click.

## FAQ

### Where do I find my MCP URL and access token?

Both are in the PipSync dashboard under the connectors/MCP settings. They are personal to your account, so they are never shown on public pages. Copy them from there when you add the connector, and treat the token like a password.

### The connector is added but shows no tools — why?

Usually MCP access is not yet enabled on your account (it is early access and rolled out in stages), or the URL/token was pasted incompletely. Re-copy both from the dashboard and re-authenticate; if tools still do not appear, remove and re-add the connector in a fresh chat.

### Do Claude and ChatGPT use the same steps?

Yes. MCP is a shared standard, so both clients add PipSync the same way: open connector settings, paste the URL, authenticate with your token, and the trading tools appear. Any MCP-compatible assistant follows the same flow.

### Is it safe to paste my token, and can I revoke it?

Your token authenticates the connector and only grants trading scope — it can never move or withdraw money. Keep it private, and if you ever suspect it leaked, rotate or revoke it in the dashboard and re-add the connector with the new one.

### I followed the steps but still can't place trades — why?

The most common reason is that MCP execution is not yet enabled for your account during the early-access rollout, so reads work but writes are held back. Reading your account confirms the connection is fine; execution switches on as the rollout reaches you.

## Related

- [Connect Claude & ChatGPT to MT5 — trade by asking, via MCP](https://pipsync.io/en/claude-chatgpt-to-mt5)
- [Signal copier with no VPS — execution runs in the cloud](https://pipsync.io/en/signal-copier-no-vps)
- [Server-side risk management — trading rules enforced before your broker](https://pipsync.io/en/server-side-risk-management)
- [AI forex signal parser — any format, any language, no templates](https://pipsync.io/en/ai-signal-parser)
- [Telegram to MT5 — copy signals to MetaTrader 5 automatically](https://pipsync.io/en/telegram-to-mt5)

---

PipSync is a signal execution tool. It does not provide trading signals, does not guarantee any trading results and is not investment advice. Trading leveraged products involves substantial risk of loss.
